! This version of Internet Explorer is not supported anymore !

We recommend to visit our website with another browser (Microsoft Edge, Chrome, Firefox, ...)

Detectors

The light automatically switching on when you enter the room? Your heating switching on automatically? Your lighting adjusting itself to the daylight entering the room? Our detectors take care of it all. With a few detectors in the right place, you will not only get used to the comfort quickly, but you will feel much safer and save a lot on your energy bill.

  • Motion detectors: automatically switch the indoor or outdoor lighting on and off when entering a room or certain zone.
  • Twilight switches: automatically switch on the outdoor lighting when it gets dark outside.
  • Daylight control: adjusts the intensity of your indoor lighting according to the amount of daylight entering the room.
  • Thermostats: measure the temperature and adjust your heating automatically to your preferred temperature.

Maximum comfort and minimal energy consumption? You can combine different kinds of detectors: for example daylight control with motion detectors.

Filters

Will the product be used indoors or outdoors?
What should be detected?
Which kind of installation or system will be used?
Which technology should the detector use for sensing?
Dual tech = a combination of passive infrared and ultrasonic PIR = passive infrared
How wide should the detector angle be?
How far should the detection reach?
How will the product be mounted?
Cabinet = in an electrical cabinet / DIN rail Flush mounting = in a suspended ceiling Flush-mounting box = in a flush-mounting box Surface mounting = on the surface of a wall or ceiling
Where should the product be mounted?
How high will the detector be mounted?
What colour should the detector be?
How dust- and waterproof should the detector be?
The higher the IP degree, the better the protection. The first digit indicates the level of dust protection, the second digit indicates the level of water protection.

Motion detector, 230 V, 12 m, 200°, IP55, for wall and ceiling mounting, for surface mounting

This outdoor motion detector with a detection range of 14 metres is suitable for use along driveways, under carports or in the garden. The motion detector can be mounted onto the ceiling or the wall and can be aimed upwards, downwards, left and right. The device has a built-in light sensor and switches the lighting automatically. After the pre-set time delay, the light is switched off automatically. The detector can be configured both manually and by remote control.

Motion detector, 230 V, 16 m, 180°, IP54, for surface mounting

The outdoor motion detector with one channel to be surface mounted on a wall or partition is suitable for use on driveways and in gardens. Equipped with an integrated light sensor. Automatic on/off (after switch-off delay) or manual on/off via an NC push button (to be ordered separately). The detection area can be divided by means of an adjustable cover mask. In conformity with the European directive for EMC and safety EN60669-2-1.

Motion detector, 230 V, 13 m, 180°, IP54, for surface mounting

The outdoor motion detector with one channel to be surface mounted on a wall or partition is suitable for use on driveways and in gardens. Equipped with an integrated light sensor. Automatic on/off (after switch-off delay) or manual on/off via an NC push button (to be ordered separately). The detection area can be divided by means of an adjustable cover mask. In conformity with the European directive for EMC and safety EN60669-2-1.

Motion detector, 230 V, 16 m, 180°, IP54, with orientable lens, for surface mounting

One-channel outdoor motion detector for use along driveways, in gardens, ... Provided with an integrated light sensor. Automatically on or manually on via a NC push button (230 V) (to be ordered separately). Automatically off after switch-off delay. Provided with a rotatable motion sensor. The detection area can be subdivided by means of an adjustable cover mask. In conformity with the European directive for EMC and safety EN60669-2-1.

Motion detector, 230 V, 13 m, 180°, IP54, with orientable lens, for surface mounting

One-channel outdoor motion detector for use along driveways, in gardens, ... Provided with an integrated light sensor. Automatically on or manually on via a NC push button (230 V) (to be ordered separately). Automatically off after switch-off delay. Provided with a rotatable motion sensor. The detection area can be subdivided by means of an adjustable cover mask. In conformity with the European directive for EMC and safety EN60669-2-1.

Motion detector, 230 V, 16 m, 300°, IP54, for surface mounting

This outdoor motion detector, which is not activated by pets, is perfectly suitable for every light switch around the house. The detection range is 16 meters. The motion sensor can be precisely aimed, both horizontally (left, right) and vertically (high, low). The device has a built-in light sensor and switches the lighting on automatically or manually with a N.O. push button (to be ordered separately). After the pre-set time delay, the light is switched off automatically. This detector can be configured both manually and by remote control.

Motion detector, 230 V, 16 m, 240°, IP54, for surface mounting

This outdoor motion detector, which is not activated by pets, is perfectly suitable for every light switch around the house. The detection range is 16 meters. The motion sensor can be precisely aimed, both horizontally (left, right) and vertically (high, low). The device has a built-in light sensor and switches the lighting on automatically or manually with a N.O. push button (to be ordered separately). After the pre-set time delay, the light is switched off automatically. This detector can be configured both manually and by remote control.

Twilight switch, 230 V, 2 lux – 200 lux, IP54

Twilight switch for outdoor wall mounting (IP54). Suitable for switching outdoor lighting. Large sensor surface for accurate light measuring. In conformity with the European directive for EMC and safety EN60669-2-1.

Twilight switch, 230 V, 3 lux – 300 lux, IP54

The twilight switch for outdoor wall mounting is suitable for controlling outdoor lighting (gardens, car parks, outdoor areas and footpaths). In conformity with the European directive for EMC and safety EN60669-2-1.

Daylight control module with twilight switch, 230 V, 3 lux – 300 lux, 2-wire

Daylight control module with twilight switch is durable and functional. It is a complete set containing the daylight control module and twilight switch. The daylight control module is suitable for car parks, outdoor areas, footpaths… The lighting is switched on automatically once the light level is below the preset level (standard setting: 35 lux). In the morning the lighting switches off automatically once the set lux level is exceeded by 10 %. The lux level is easy to set using the potentiometer on the daylight control module. There is a double cable connecting the daylight control module and the twilight switch.

Lighting control module, 230 V, 3 lux – 30000 lux

Energy-saving thanks to optimum use of lighting. Modular lighting control to be used in combination with a photocell and motion detector(s). Automatically switching on depending on the measured daylight level and motion detection. Automatically switching off in case of sufficient daylight or after a switch-off delay. Optional control via an N.O. push button (to be ordered separately). Suitable for indoor and outdoor applications.

Motion detector M42MR, 230 V, 12-13 m, for flush-mounting box

This flat and discrete motion detector is a 1-channel, stand-alone detector for automatic lighting control. The detector is specially designed for mounting in a standard flush-mounting box (60 or 79 mm screw distance). The detector’s settings can be modified using the Niko detector tool app and 2-way Bluetooth® communication between a smartphone and the detector.

Motion detector M42MR, 230 V, 12-13 m, for flush mounting (SnapFit)

This flat and discrete motion detector is a 1-channel, stand-alone detector for automatic lighting control. The SnapFit mounting bracket ensures a quick and stable mounting in all types of suspended ceilings with or without removable tiles. The detector’s settings can be modified using the Niko detector tool app and 2-way Bluetooth® communication between a smartphone and the detector.

Motion detector M42MR, 230 V, 12-13 m, IP54, for surface mounting

This motion detector is a 1-channel, stand-alone detector for automatic lighting control. The detector is designed for surface mounting and has an IP54 protection degree. The detector’s settings can be modified using the Niko detector tool app and 2-way Bluetooth® communication between a smartphone and the detector.

Motion detector M42LR, 230 V, 32-37 m, for flush-mounting box

This motion detector is a 1-channel, stand-alone detector with a large detection range for automatic lighting control. The detector is specially designed for mounting in a standard flush-mounting box (60 or 79 mm diagonal screw distance). The detector’s settings can be modified using the Niko detector tool app and 2 way Bluetooth® communication between a smartphone and the detector.

Motion detector M42LR, 230 V, 32-37 m, for flush mounting (SnapFit)

This motion detector is a 1-channel, stand-alone detector with a large detection range for automatic lighting control. The SnapFit mounting bracket ensures a quick and stable mounting in all types of suspended ceilings with or without removable tiles. The detector’s settings can be modified using the Niko detector tool app and 2-way Bluetooth® communication between a smartphone and the detector.

Motion detector M42LR, 230 V, 32-37 m, IP54, for surface mounting

This motion detector is a 1-channel, stand-alone detector with a large detection range for automatic lighting control. It is designed for surface mounting and has an IP54 protection degree. The detector’s settings can be modified using the Niko detector tool app and 2-way Bluetooth® communication between a smartphone and the detector.

Motion detector M42HC, 230 V, master, 18-53 m, IP54, for high ceilings, for surface mounting

This high ceiling detector is a 1-channel master detector with a large detection range for automatic lighting control. It is designed for surface mounting and has an IP54 protection degree. The detector’s settings can be modified using the Niko detector tool app and 2-way Bluetooth® communication between a smartphone and the detector.

Motion detector M41HC, 230 V, secondary, 18-53 m, IP54, for high ceilings, for surface mounting

This high ceiling detector is a secondary detector that extends the detection range of a high ceiling 230 V master detector. It is designed for surface mounting and has an IP54 protection degree. The detector’s settings can be modified using the Niko detector tool app and 2-way Bluetooth® communication between a smartphone and the detector.

Motion detector, 230 V, 8 m, 180°, wall detector, for flush-mounting box

This motion detector is used for LED, economy lamps, 230 V halogen lamps, low voltage halogen lamps and fluorescent lamps. For indoor use only.

Motion detector, 230 V, 14 m, round, for flush-mounting box

The motion detector with one channel for flush mounting in ceilings is suitable for switching indoor lighting on and off. You can always activate the light with a NO push button (230 Vac) (to be ordered separately). The detector is equipped with an integrated light sensor.

Motion detector, 230 V, 26 m, round, for flush-mounting box

The motion detector with one channel for flush-mounting in ceilings is suitable for switching indoor lighting on and off. You can always activate the light with a NO push button (230 Vac) (to be ordered separately). The detector is equipped with an integrated light sensor.

Motion detector, 230 V, 26 m, IP55, for surface mounting

The motion detector with one channel for surface mounting on ceilings is suitable for switching indoor lighting on and off. The detector is equipped with an integrated light sensor.

Motion detector, 230 V, 40 m, for corridors, for flush-mounting box

The one channel corridor motion detector is suitable for automatic indoor lighting control (on/off). It can be installed in a flush-mounting box in the ceiling. Flush-mounting box with springs and an IP54 surface-mounting box can be ordered separately. In conformity with the European directive for EMC and safety EN60669-2-1.

...