Compound socket outlet (base and finishing set) with pin earthing. The base is equipped with screw terminals and claw fixing. The socket outlet also has a safety shutter and a flush-mounting depth of 21 mm. Finishing colour: cream
Socket outlet with earth pin and safety shutter, flush-mounting depth 21 mm, base, screw terminals and finishing set cream.
Base for socket outlet with pin earthing and safety shutters, flush-mounting depth 21 mm, 16 A/250 Vac, screw terminals. The socket outlet is provided with contact buses with a large contact surface that do not rest on the base in order to clasp. The sockets are fitted with cage clamps with permanent screws. These screws have combination screwheads (Pz2 or slot 1 x 6 mm). Moreover, every screw is provided with a screwdriver slot that prevents the screwdriver from sliding off the screwhead. All connection terminals are located at the top of the end socket and can contain up to 4 x 2.5 mm² of wire. The earthing terminal even up to 2 x 2.5 mm² + 2 x 4 mm². The stripping length (14 mm) of the wires is indelibly imprinted on the back of the base. When mounting the socket outlet in a flush-mounting box with grip surfaces, use claws that can be rotated open using screws with a combination screwhead (Pz2 or slot 1 x 5.5 mm). The claws, which have an engagement depth of 23.5 mm, turn back completely when loosened. The flush-mounting frame is made from 1 mm-thick metal which is galvanized on all sides after cutting, even on the cut edges. On the horizontal and vertical axes, the flush-mounting frame has 4 grooves for screw mounting in flush-mounting boxes. These grooves have a screw aperture of 7 mm. For mounting on panels, the flush-mounting frame is equipped with 4 screw holes (indicated by a screw symbol) with a diameter of 3 mm. The middle of the flush-mounting frame is indicated (chalk line, laser, ..) in both the horizontal and vertical directions, so that mounting one or more mechanisms can be carried out quickly and easily. At the right and left sides, the flush-mounting frame is equipped with folded-up dovetails, allowing for a quick and perfect horizontal coupling of several switches. The folded-up edges on the outside of the base and their continuation to the inside ensure additional robustness. The bases can be coupled vertically with a centre-to-centre distance of 60 x 71 mm by sliding them into each other. They automatically lock into place. For horizontal coupling of bases with a centre-to-centre distance of 71 mm, the base is equipped with two pre-formed lips at the bottom. By folding these lips down over a length of 1 mm, this rests perfectly on the one below and the centre-to-centre distance of 71 mm is guaranteed. The 4 rectangular openings (7 x 2.5 mm) in the flush-mounting frame can compensate for a margin of 1 to 1.2 mm if the flush-mounting box protrudes beyond the plasterwork. In the case of such a margin, the flush surround plate can still butt up perfectly against the wall.
Finishing set for socket outlet with earth pin and safety shutter, flush-mounting depth 21 mm. The central plate is fixed to a flush-mounting socket outlet using a screw with a combination screwhead (Pz1 slot 1 x 5.5 mm). The back of the central plate is equipped with a safety shutter. This allows contact to be made after simultaneous introduction of the pins of a plug but prevents contact from being made if only 1 pin is introduced or if the two pins are not introduced simultaneously. This central plate is surrounded with a flat edge that is equipped at all 4 corners with a rectangular opening, each containing a multi-positional snap hook. The construction of the central plate ensures that the flush-surround plate can always be attached flat to the wall, even in cases of untidy plasterwork. This works in two directions: If the flush-mounting box sticks out of the plasterwork, the multi-positional snap hooks can compensate for a 1 to 1.2 mm margin; if the flush-mounting box is sunk too deeply in the plasterwork, the snap hooks can compensate for up to a 1.8 mm margin. The flat edge around the central plate also has 4 round openings that ensure the correct positioning of the flush surround plate in relation to the central plate. After mounting all components (flush surround plate, finishing set and switch), no metal parts are visible thanks to the flat edge of the central plate. To dismount simply unscrew the central plate.
Dimensions of visible area of finishing: 45 x 45 mm (HxW)