Wireless 2-channel receiver, IP66, for surface mounting
The two-channel receiver for surface mounting is provided with two switching contacts (10 A/230 V) (two-way contact and single-pole contact) and two push-button inputs. The receiver can be controlled without any wiring or via local push buttons. If the receiver is used as a roll-down shutter or ventilation control, there are five specific modes for setting the roll-down shutter functions (open, stop and close) or the different ventilation speeds. When used as a motor control, both contacts are used for one motor. The receiver can only be connected to one phase. The switching contacts cannot be used for safety extra-low voltage (SELV) circuits.
Product details
Surface-mounting RF receiver, IP66 with 2 channels
This surface-mounting receiver is protected against dust and powerful water jets (IP66). You control it wirelessly or with push buttons. It has 2 10A/ 230V switch contacts (two-way and 1-pole contacts) and 2 push-button inputs. You can choose from 5 modes for the on/off functions. These can be independently set for each output. You set the operating time to between 0 and 3 seconds and the switch-off time between 0 and 120 minutes. Do you use the 2-channel receiver for the control of roller shutters or a ventilator? Then you have the following specific function settings:
- opening, closing or stopping the roller shutters;
- setting the speed of the ventilator.
Will you use the receiver for the control of a motor? Then, the device uses both contacts for one motor. You may only use it in a 1-phase distribution network. The contact may not be used for circuits with safety extra-low voltage (SELV).
Specification description
Surface-mounting RF receiver, IP66 with 2 channels
- Not compatible with the wireless bridge, nor with the wireless smart hub
- Maximum MCB rating: 10 A (limited by national installation rules)
- Communication protocol: Easywave
- Maximum radio frequency power: -11.29 dBm
- Operating frequency: 0.8683 GHz
- Protection degree: IP66
- Weight: 645 g
- Dimensions (HxWxD): 56 x 94 x 180 mm
- Marking: CE
Related products
Wireless battery-powered switch, 1-fold, Zigbee®
This onefold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72001) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the onefold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72011). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).
Wireless battery-powered switch, 2-fold, Zigbee®
This twofold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72002) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the twofold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72012). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).
Wireless battery-powered switch, 4-fold, Zigbee®
This fourfold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in your Niko Home Control installation or connected to a third-party Zigbee® network as a standard dimmer switch via Find&Bind pairing. Moreover, the switch can be paired with up to eight Zigbee® receivers for stand-alone use via Touchlink. It is battery-powered with a lifetime of at least five years, based on twenty short-press actuations a day. The wireless Zigbee® switch is mounted on a plastic base. The set (base + switch 552-72004) can be screwed on a wall (screws excluded) or glued to a flat surface with double-sided adhesive tape (included). If you want to install the fourfold wireless battery-powered Zigbee® on a flush-mounting box, order the variant without plastic baseplate (552-72014). Combine it with a metal baseplate (552-720X0) instead. The wireless battery-powered switch can be connected wirelessly to the wireless smart hub for Niko Home Control (552-00001). This device can also be used in a bus wiring installation in combination with the wireless bridge for Niko Home Control (550-00640).
