! This version of Internet Explorer is not supported anymore !

We recommend to visit our website with another browser (Microsoft Edge, Chrome, Firefox, ...)

Wireless two-channel receiver, IP66, for surface mounting

The two-channel receiver for surface mounting is provided with two switching contacts (10 A/230 V) (two-way contact and single-pole contact) and two push-button inputs. The receiver can be controlled without any wiring or via local push buttons.  If the receiver is used as a roll-down shutter or ventilation control, there are five specific modes for setting the roll-down shutter functions (open, stop and close) or the different ventilation speeds. When used as a motor control, both contacts are used for one motor. The receiver can only be connected to one phase. The switching contacts cannot be used for safety extra-low voltage (SELV) circuits.

Product details

This product consists of several components. Below you will find an overview of all the component parts.
Technical datasheets
Technical manuals
Certificaten CE-Marking

Surface-mounting RF receiver, IP66 with 2 channels

Reference code
05-336

This surface-mounting receiver is protected against dust and powerful water jets (IP66). You control it wirelessly or with push buttons. It has 2 10A/ 230V switch contacts (two-way and 1-pole contacts) and 2 push-button inputs. You can choose from 5 modes for the on/off functions. These can be independently set for each output. You set the operating time to between 0 and 3 seconds and the switch-off time between 0 and 120 minutes. Do you use the 2-channel receiver for the control of roller shutters or a ventilator? Then you have the following specific function settings:

  • opening, closing or stopping the roller shutters;
  • setting the speed of the ventilator.

Will you use the receiver for the control of a motor? Then, the device uses both contacts for one motor. You may only use it in a 1-phase distribution network. The contact may not be used for circuits with safety extra-low voltage (SELV).

Technical characteristics:

  • dimensions: L180xW94xD56mm.

Specification description

Surface-mounting RF receiver, IP66 with 2 channels

Splashproof surface-mounting receiver, wirelessly controlled via radio frequency (868.3MHz) and/or via local push buttons. Equipped with two potential-free switching contacts, 1 single pole and 1 switch, 10A, 230V 50Hz. Choice of 5 modes for the on/off functions can be set separately for each output. Maximum 32 transmitters per receiver. Protection degree: IP66. Max. reception range in a building: 30 m; in open field 100 m. Dimensions: 94 x 180 x 56mm. Power supply: 230V 50Hz. Modulation type: FSK. In accordance with Belgian and European legislation: CE marked. This product complies with all of the relevant European guidelines and regulations. For radio equipment, Niko nv declares that it is in compliance with Directive 2014/53/EU. May be used in all European member states. Manual is included.

  • Communication protocol: Easywave®
  • Marking: CE

Related products

Niko dimmer switch for Hue system

With this wireless and battery-free dimmer switch, you can effortlessly operate Philips Hue lamps. Determine in the Philips Hue app what each button must do (switching on and off, dimming, activating scene settings). No wall breaking or cable installation is needed. The dimmer switch can be mounted on a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive strips (included). Please note that Philips Hue Bridge v2 is required and not included.

Wireless switch with four buttons

This wireless switch with four buttons can be used by a smart switch or a wireless receiver. It can be used as a two dual-button controls (upper:on, lower off) or as four one-button controls (on/off or pulse). The switch can also be used in the Niko Home Control installation for bus wiring in combination with the USB RF interface Easywave (410-00099) for Niko Home Control or in the Niko Home Control installation for traditional wiring in combination with the wireless smart hub (552-00001).

Smart single switch with push button and RF extensions, 10 A

The smart switch has a switching contact to switch lighting on and off. It has a transmitter and receiver operating according to the Easywave protocol. If desired, extra controls can be added. These could be both classic wired push buttons and wireless controls according to the Easywave protocol. By doing so, it can effortlessly replace any traditional single, multiway, or intermediate switching. This makes the smart switch especially suitable for renovation projects or listed building interiors in which drilling or channelling work should be avoided. Please note, the only condition for the use of the smart switch is the presence of the neutral conductor in the flush-mounting box where the smart switch will be placed. Besides being able to switch its own contact, the smart switch is also able to switch other receivers operating according to the Easywave protocol. This function can also be incorporated in a scene setting/preset. In doing so, you can switch all lighting included in the scene setting/preset with one push of the button. It is fitted with a feedback LED of which the behaviour can be adapted to the needs of the user.

Favorites ( 0 )