Wireless one-channel receiver, for flush mounting
The wireless Easywave receiver with 230 V two-way switching contact (one-channel) is suitable for flush mounting and may only be used as a wireless Easywave control in combination with small electrical loads. This wireless Easywave receiver can be switched in one of the following three working modes: two modes for the on-off function and pulse mode. You can operate the receiver using either wireless Easywave push buttons (410-0000x) or hand-held Easywave transmitters.
Product details
Wireless Easywave receiver with 230 V two-way switching contact (one-channel)
The wireless Easywave receiver with 230 V two-way switching contact (one-channel) is suitable for flush mounting and may only be used as a wireless Easywave control in combination with small electrical loads. This wireless Easywave receiver can be switched in one of the following three working modes: two modes for the on-off function and pulse mode. You can operate the receiver using either wireless Easywave push buttons (410-0000x) or hand-held Easywave transmitters.
Specification description
Wireless Easywave receiver with 230 V two-way switching contact (one-channel)
The wireless Easywave receiver with 230 V two-way switching contact (one-channel) is suitable for flush mounting and may only be used as a wireless Easywave control in combination with small electrical loads. This wireless Easywave receiver can be switched in one of the following three working modes: two modes for the on-off function and pulse mode. You can operate the receiver using either wireless Easywave push buttons (410-0000x) or hand-held Easywave transmitters. The product is part of the Easywave radio frequency system, a wireless installation technique between the push buttons (control points) and the consumers to be operated. The Easywave system is a modular system with transmitters and receivers. A wireless Easywave wall transmitter has the form of a push button with two or four action buttons and can be mounted on a wall. A hand-held transmitter looks like a traditional remote control unit. One transmitter can operate an unlimited number of receivers simultaneously, while one receiver can be controlled by a maximum of 32 transmitters. The remote control or wireless control operates on the basis of signal transmission via radio waves at a frequency of 868.3 MHz. This frequency only allows products that emit signals no more than 1% per hour or 36 seconds, which reduces the risk of interrupted signals to an absolute minimum. Therefore, the wireless Easywave system is excellently suited to specific applications, such as renovations of listed interiors, extensions of existing electrical installations (where drilling or channelling is not possible), for use in offices with moveable partitions or walls or in installations where complicated wiring must be avoided.
- Communication protocol: Easywave®
- Marking: CE
Related products
Niko dimmer switch for Hue system
With this wireless and battery-free dimmer switch, you can effortlessly operate Philips Hue lamps. Determine in the Philips Hue app what each button must do (switching on and off, dimming, activating scene settings). No wall breaking or cable installation is needed. The dimmer switch can be mounted on a European flush-mounting box, screwed onto a wall (screws not included) or glued to a flat surface with double-sided adhesive strips (included). Please note that Philips Hue Bridge v2 is required and not included.
Smart single switch with push button and RF extensions, 10 A
The smart switch has a switching contact to switch lighting on and off. It has a transmitter and receiver operating according to the Easywave protocol. If desired, extra controls can be added. These could be both classic wired push buttons and wireless controls according to the Easywave protocol. By doing so, it can effortlessly replace any traditional single, multiway, or intermediate switching. This makes the smart switch especially suitable for renovation projects or listed building interiors in which drilling or channelling work should be avoided. Please note, the only condition for the use of the smart switch is the presence of the neutral conductor in the flush-mounting box where the smart switch will be placed. Besides being able to switch its own contact, the smart switch is also able to switch other receivers operating according to the Easywave protocol. This function can also be incorporated in a scene setting/preset. In doing so, you can switch all lighting included in the scene setting/preset with one push of the button. It is fitted with a feedback LED of which the behaviour can be adapted to the needs of the user.
Smart double switch with push button and RF extensions, 2 x 10 A
The smart switch has two switching contacts of 10 A each (in total max 16 A) to switch lighting on and off. It has a transmitter and receiver operating according to the Easywave protocol. If desired, extra controls can be added. These could be both classic wired push buttons and wireless controls according to the Easywave protocol. By doing so, it can effortlessly replace any traditional single, multiway, or intermediate switching. This makes the smart switch especially suitable for renovation projects or listed building interiors in which drilling or channelling work should be avoided. Please note, the only condition for the use of the smart switch is the presence of the neutral conductor in the flush-mounting box where the smart switch will be placed. Besides being able to switch its own contact, the smart switch is also able to switch other receivers operating according to the Easywave protocol. This function can also be incorporated in a scene setting/preset. In doing so, you can switch all lighting included in the scene setting/preset with one push of the button. It is fitted with a feedback LED of which the behaviour can be adapted to the needs of the user.
