Double, horizontal socket outlet with earth pin and safety shutter, screw terminals, flush-mounting depth of 21 mm, incl. flush surround plate cream

100-66102

Description

Compound double socket outlet with earth pin (base, finishing set and flush surround plate) for horizontal positioning. The bases are equipped with screw terminals . The socket outlet also has a safety shutter and a flush-mounting depth of 21 mm. Finishing colour: cream

Specification description

Double, horizontal socket outlet with earth pin and safety shutter, screw terminals, flush-mounting depth of 21 mm, incl. flush surround plate cream.

  • Certification marks: CEBEC, NF
  • Marking: CE

Base for horizontal, double socket outlet with earth pin and safety shutter, flush-mounting depth 21 mm, screw terminals. Both bases of the socket outlet are equipped with contact buses with a large contact surface that do not rest on the base in order to be connected. The two bases are welded to each other using a metal plate. The sockets are fitted with cage clamps with permanent screws. These screws have combination screwheads (Pz2 or slot 1 x 6 mm). Moreover, every screw is provided with a screwdriver slot that prevents the screwdriver from sliding off the screwhead. All connection terminals are located at the top of the end socket and can contain up to 4 x 2.5 mm² of wire. The earthing terminal even up to 2 x 2.5 mm² + 2 x 4 mm². The stripping length (14 mm) of the wires is indelibly imprinted on the back of the base. On the horizontal axis, the grooves each have two screw holes of 7 mm so that the socket outlet can be easily mounted in a flush-mounting box. In this configuration, the screws are on the horizontal axis or in channelling systems with which the double, pre-wired socket outlet must be attached to the mounting brackets. By means of the screw holes, the flush-mounting frame is positioned over the screwheads of the screws of the flush-mounting box or mounting bracket and is then shifted to the desired position and screwed tight. For attachment to flush-mounting boxes where the screws are positioned on the vertical axis, the grooves are on the vertical axis, each one equipped with one screw hole. Thanks to the 7 mm screw holes, the flush-mounting frame is positioned over the screwheads of the screws of the flush-mounting box and is then shifted to the left in order to be attached in the correct position. The flush-mounting frame is made from 1 mm-thick metal which is galvanized on all sides after cutting, even on the cut edges. On the horizontal and vertical axes, the flush-mounting frame has 4 grooves for screw mounting in flush-mounting boxes. These grooves have a screw aperture of 7 mm. For mounting on panels, the flush-mounting frame is equipped with 4 screw holes (indicated by a screw symbol) with a diameter of 3 mm. The middle of the flush-mounting frame is indicated (chalk line, laser, ..) in both the horizontal and vertical directions, so that mounting one or more mechanisms can be carried out quickly and easily. At the right and left sides, the flush-mounting frame is equipped with folded-up dovetails, allowing for a quick and perfect horizontal coupling of several switches. The folded-up edges on the outside of the base and their continuation to the inside ensure additional robustness. The bases can be coupled vertically with a centre-to-centre distance of 60 x 71 mm by sliding them into each other. They automatically lock into place. For horizontal coupling of bases with a centre-to-centre distance of 71 mm, the base is equipped with two pre-formed lips at the bottom. By folding these lips down over a length of 1 mm, this rests perfectly on the one below and the centre-to-centre distance of 71 mm is guaranteed. The 4 rectangular openings (7 x 2.5 mm) in the flush-mounting frame can compensate for a margin of 1 to 1.2 mm if the flush-mounting box protrudes beyond the plasterwork. In the case of such a margin, the flush surround plate can still butt up perfectly against the wall.

  • Protection degree: The combination of a switch, a central plate and a flush surround plate has a protection degree of IP41.
  • Flush-mounting depth: 21 mm
  • Certification marks: CEBEC, NF
  • Marking: CE

Finishing set for socket outlet with earth pin and safety shutter, flush-mounting depth 21 mm. The central plate is fixed to a flush-mounting socket outlet using a screw with a combination screwhead (Pz1 slot 1 x 5.5 mm). The back of the central plate is equipped with a safety shutter. This allows contact to be made after simultaneous introduction of the pins of a plug but prevents contact from being made if only 1 pin is introduced or if the two pins are not introduced simultaneously. This central plate is surrounded with a flat edge that is equipped at all 4 corners with a rectangular opening, each containing a multi-positional snap hook. The construction of the central plate ensures that the flush-surround plate can always be attached flat to the wall, even in cases of untidy plasterwork. This works in two directions: If the flush-mounting box sticks out of the plasterwork, the multi-positional snap hooks can compensate for a 1 to 1.2 mm margin; if the flush-mounting box is sunk too deeply in the plasterwork, the snap hooks can compensate for up to a 1.8 mm margin. The flat edge around the central plate also has 4 round openings that ensure the correct positioning of the flush surround plate in relation to the central plate. After mounting all components (flush surround plate, finishing set and switch), no metal parts are visible thanks to the flat edge of the central plate. To dismount simply unscrew the central plate.

  • Protection degree: The combination of a switch, a central plate and a flush surround plate has a protection degree of IP41.
  • Material central plate: The central plate is made of rigid PC and ASA. The base material is coloured in mass.
  • Colour: cream (coloured in mass, approximately RAL 1013)
  • Impact resistance: After mounting, an impact-resistance of IK06 is guaranteed.
  • The plastic parts of the central plate are self-extinguishing (comply with a filament test of 650°C) and are halogen-free.
  • Dimensions of finishing with flat edge: 56 x 56 mm (HxW)

Dimensions of visible area of finishing: 45 x 45 mm (HxW)

Double flush surround plate with 71 mm centre-to-centre distance Original cream. Double flush surround plate for two switches. The complete flush surround plate is self-extinguishing (complies with a filament test of 650°C) and halogen-free. It is made of dimensionally stable pc+asa.

  • Colour: cream (coloured in mass, approximately RAL 1013)
  • Surface-mounting height: max. 8.5 mm
  • Dimensions (HxWxD): 83 x 154 x 8.9 mm
  • Certification marks: CEBEC, ÖVE, KEMA, VDE, NF, SEMKO
  • Marking: CE

Related articles

list 0
Favorites